car35

Car Amplifier Basics

Lets start by recognizing the different types of amplifiers. You’ve got your basic mono channel amplifier, your two channel amplifier, and then you have multiple channel amplifiers. A “channel” is simply one set of positive and negative terminals ( /-) coming out of the amplifier that you use to supply power, or drive, to your speakers or subwoofers. A mono channel amplifier has one set of terminals, two channel amplifiers have two, and multiple channel amplifiers range from anywhere between 3-5 channels. Now lets go into details discussing their best intended applications. We’ll also answer the questions that are asked most frequently.

Mono Channel Amplifers- Mono channel amplifiers tend to be class “D” amplifiers. Class “D” amplifiers have a high power to heat ratio, which is exactly what you are looking for when powering subwoofers that demand a lot of power. Class “D” amplifiers are also known to be very efficient. Since mono channel amplifiers work best at 2 ohms of impedance, they are best suited to drive either a singe 4 ohm “dual voice coil” subwoofer, or two 4 ohm subwoofers that only have “one voice coil” each.

Why are mono channel amps best suited for these setups? Because every speakers presents a load impedance to the power that is supplied to it from the amplifier. This load impedance is measured in a unit known as “ohms”. Most subwoofer speakers present 4 ohms of resistance. If wired correctly, you will lower the load impedance that the amplifier sees. You will lower the impedance down to 2 ohms, which is where most mono channel amplifiers are build to perform the best.

Two Channel Amplifiers- A two channel amplifier is an amplifier that can operate one right, and one left hand channel. It is basically two mono channel amplifiers in a single box. Since two channel amplifiers are typically stable when presented with 4 ohms of impedance, they are best suited to drive either one 4 ohm “single voice coil” subwoofer, or two 4 ohm “dual voice coil” subwoofers. To run these setups, you have to “bridge” the channels coming from the amplifier. Not all two channel amplifiers are bridgeable, so be sure that your two channel amp is bridgeable before you buy it.

What is “bridging”? Lets say that you are looking to purchase a two channel amplifier that is rated at 500 watts RMS. You must know that the amplifier does not supply 500 watts of power from each channel. Instead, each channel alone will supply around 200-250 watts. In order to get the advertised 500 watts, you have to combine the two channels into one channel. This is called “bridging” the channels.

*Note- Be careful when “bridging” the connections because if it not done properly, then you will destroy your amplifier.

Multiple Channel Amplifiers- Multiple channel amplifiers allow you to hook up multiple speakers (typically front two and rear two) while still allowing you to control your balance and fading options. When shopping for multiple channel amplifiers, you will find that although most are still rated in the 2-4 ohm impedance range, some are rated around 20-40 ohms of impedance. The only time you would ever need an amplifier at this high of an impedance rating is if you were to wire multiple speakers in a “series”. Multiple channel amplifiers can be used to run subwoofers, but you have to make sure that the amplifier’s channels are bridgeable since most of the time, each channel of a multiple channel amplifier does not give out nearly enough watts.

What is “series” wiring? Instead of wiring each speaker separately to each channel of an amplifier, sometimes it is recommended that you wire two or more speakers together. Once the speakers are wired together, you want to wire the entire unit of speakers to one channel of the amplifier. To wire the speakers together, you simply run a speaker wire from the positive terminal of one speaker to the negative terminal of another speaker. Once this is done, you run speaker wires from the channels of your amp to your remaining positive and negative terminals on your speakers.

*Note- You must keep track of load impedance when you are wiring speakers in “series”. When wiring in a series, you simply add up the number of ohms of each speaker. Make sure your amp is rated to run at that high of an impedance.

Check out http://www.DominantCarAudio.com for more information about car audio, and for the largest selection of quality car audio equipment at the best possible prices.

http://www.dominantcaraudio.com

Article Source: http://www.articleslash.net

x

Check Also

car30

Confort and control in 2017 Volvo S90 sedan

Confort and control in 2017 Volvo S90 sedan Volvo recently introduced the highly-anticipated Volvo S90 luxury sedan on the heels of the company's award-winning Volvo XC90 SUV. The all-new 2017 ...

car34

Rolls-Royce Holding PLC (RR) Given Neutral Rating at Credit Suisse

Rolls-Royce Holding PLC (RR) Given Neutral Rating at Credit Suisse Rolls-Royce Holding PLC logo Rolls-Royce Holding PLC (LON:RR)'s stock had its “neutral” rating reiterated by equities research analysts at Credit ...

car23

Why GM will import the Cadillac CT6 PHEV from China

Why GM will import the Cadillac CT6 PHEV from China There's a clear-cut reason that General Motors is going to build its upcoming plug-in hybrid CT6 sedan in China. Sure, ...